FS/FT 1999 GMC Sonoma 2.2l 5spd (bagged, shaved, etc etc) ^-^
#1
FS/FT 1999 GMC Sonoma 2.2l 5spd (bagged, shaved, etc etc) ^-^
$3750 OBO OR TRADE
I will take trades on a 240, ae86, fc3s, etc (something driftable)
or a stunt piece... f4i or 636 preferably
The truck is driven daily so miles may climb a lil
1999 Somona
2.2L
5- speed
~80k mi
S10 front end
shaved gate & molded pan
e-fan
xplode head unit and speakers
Full air ride (all purchased from suicide)
-2b6's up front
-2b7's over axle in the back
-3 link
-1/2 fills
-3/8 dumps
-avs 7 rocker
-sanden 7 series (blew a valve.. in the middle of putting a new one on)
-viar 450 backup <--
-4 - SMC 1/2 check valves
-5 gallon tank
-2 dual needle KP's & 1 single needle
-cavi seats,
-CIA to eliminate the huge snorkle
-ABS was moved over with all ABS connections
-The MAF sensor does have crimp on fittings if you can see it in the pics (not my work)
-Calipers, pads and front rotors have less then 1000 miles on them
-parking break DOES WORK unlike other bagged rides
-The yellow top was moved the bed for more room up front
Within the last 5k miles:
new clutch, resurfaced flywheel & new ring gear
(the ring gear was slipping so the whole assemble was replaced)
MORE PICs-->
This was built to be a reliable daily driven truck, but I dont have the time or money to finish it up. The paint is not professional but looks half decent in my opinion (There are some nicks and scratches ).
I just finished wiring up the air ride the right way (im an electrical engineer so i used top notch terminals).
The truck is 95% done but could use some paint and wheels to be finished.
Coatesville, pa 19320
btracer@comcast.net
AIM: btracer02
cell: 610-764-0785
I will take trades on a 240, ae86, fc3s, etc (something driftable)
or a stunt piece... f4i or 636 preferably
The truck is driven daily so miles may climb a lil
1999 Somona
2.2L
5- speed
~80k mi
S10 front end
shaved gate & molded pan
e-fan
xplode head unit and speakers
Full air ride (all purchased from suicide)
-2b6's up front
-2b7's over axle in the back
-3 link
-1/2 fills
-3/8 dumps
-avs 7 rocker
-sanden 7 series (blew a valve.. in the middle of putting a new one on)
-viar 450 backup <--
-4 - SMC 1/2 check valves
-5 gallon tank
-2 dual needle KP's & 1 single needle
-cavi seats,
-CIA to eliminate the huge snorkle
-ABS was moved over with all ABS connections
-The MAF sensor does have crimp on fittings if you can see it in the pics (not my work)
-Calipers, pads and front rotors have less then 1000 miles on them
-parking break DOES WORK unlike other bagged rides
-The yellow top was moved the bed for more room up front
Within the last 5k miles:
new clutch, resurfaced flywheel & new ring gear
(the ring gear was slipping so the whole assemble was replaced)
MORE PICs-->
This was built to be a reliable daily driven truck, but I dont have the time or money to finish it up. The paint is not professional but looks half decent in my opinion (There are some nicks and scratches ).
I just finished wiring up the air ride the right way (im an electrical engineer so i used top notch terminals).
The truck is 95% done but could use some paint and wheels to be finished.
Coatesville, pa 19320
btracer@comcast.net
AIM: btracer02
cell: 610-764-0785
#3
Re: FS/FT 1999 GMC Sonoma 2.2l 5spd (bagged, shaved, etc etc) ^-^
it lays frame, but the picture is taken with it on a hill
it could be lower but as good as it gets with this bag setup
it could be lower but as good as it gets with this bag setup
#5
Re: FS/FT 1999 GMC Sonoma 2.2l 5spd (bagged, shaved, etc etc) ^-^
maybe, stll thinkin. got a 04 636 that I havent rode yet (been getting it ready for the lot) dont know if I wanna get rid of it yet that truck is tempting though
Thread
Thread Starter
Forum
Replies
Last Post