more new models OMR SUBCAGES !!!
Re: more new models OMR SUBCAGES !!!
I can't find a used name brand welder for anywhere under $350 up here. Except stick welders. I've been looking for a couple years.
also known as OMR
Thread Starter
Join Date: Jul 2006
Location: OMR INDUSTRIES in west palm beach florida
Posts: 79,288
also known as OMR
Thread Starter
Join Date: Jul 2006
Location: OMR INDUSTRIES in west palm beach florida
Posts: 79,288
Re: more new models OMR SUBCAGES !!!
OMR SUBCAGE[S]
available subcages:
Honda
pay pal accepted
Tech
click here to contact >> old man roger
the original folding peg subcage!!!!!!
>>click here to see why i only sell folding peg subcages<<
available subcages:
Honda
- CBR F4i - 01, 02, 03 <<< click here, will also fit the single seat style with minor mods
- CBR 954- all years
- CBR 929- all years <<< click here
- CBR 600RR - 03 , 04 , 05 , 06 , 07 , 08<<< click here
- GSXR 600 - 01, 02, 03, 04, 05 ,06, 07<<<click here
- GSXR 750- 00, 01, 02, 03, 04, 05, 06,07 <<click here
- GSXR 1000 -01, 02, 03, 04
- R6 - 03, 04, 05 <<< click here
- R6s (old body style) - 06, 07, 08
- R1 98, 99, 00, 01
pay pal accepted
Tech
- The CBR 600RR , Yamaha R6 ,03 04 gsxr 1000 and the f4i pegs are lowered and moved back and out for better peg position! !
- The 01-03 GSXR 600 and 750 have the pegs moved out two inches because of the big tail section
- THE 07 600RR pegs are located 2-1/2 inches lower and 3 inches wider (Than stock)
- The zx6 models are slightly wider than stock to keep your leg from being pressed against the tail
- other omr subframe cage models are in the stock location except they are rotated on their axis so they don't fold up unless you fold them up, this also puts your foot on the grippy part of the peg during a wheelie.
- omr subcages are available for all makes and models but only the ones listed above are available for shipping
click here to contact >> old man roger
the original folding peg subcage!!!!!!
>>click here to see why i only sell folding peg subcages<<
also known as OMR
Thread Starter
Join Date: Jul 2006
Location: OMR INDUSTRIES in west palm beach florida
Posts: 79,288
Re: more new models OMR SUBCAGES !!!
Is a flux core welder good for anything? I might just pick up a cheap one to make some small **** around the house. Mostly 16ga to 1/8" square tubing. Nothing that has to support more than a couple hundred pounds. This is a 110v welder. 85 amp max. Says it's good to 3/16". It's only $100. It's either this or taking my steel to my buddy half an hour away every time I need something welded. I'd still take anything that needed to be done well to him. I wonder if you could run this off an extension cord. I have a 50' 12ga extension cord.
is it a good brand or chinese? if its a good brand might as well get it. 12 ga is fine
Re: more new models OMR SUBCAGES !!!
btw mine is the same physical size, (or close to it) as many of lincolns 110 volt welders. i can carry it with one arm if i had to. you wouldnt need a big garage for it, just a 220 electrical outlet and a custom extension cord. remember a 220 welder will only require half the amperage of a 110 to do that same job. And as you know its the current that melts wiring, not voltage, so you could get away with 12 gauge cord and still weld heavier stuff.
Re: more new models OMR SUBCAGES !!!
or quickly shell out the $500 before the next kid pops out
Re: more new models OMR SUBCAGES !!!
when i see one, i'll slow down and look for tools. if i see anything that looks promising i'll go back and look. like i said before, all i ever found were old wrenches and screwdrivers, or k mart tool sets
also known as OMR
Thread Starter
Join Date: Jul 2006
Location: OMR INDUSTRIES in west palm beach florida
Posts: 79,288
Re: more new models OMR SUBCAGES !!!
also known as OMR
Thread Starter
Join Date: Jul 2006
Location: OMR INDUSTRIES in west palm beach florida
Posts: 79,288
Re: more new models OMR SUBCAGES !!!
Re: more new models OMR SUBCAGES !!!
i normally wouldnt repost this one unless neal still had his rover
Re: more new models OMR SUBCAGES !!!
chicago electric??
btw mine is the same physical size, (or close to it) as many of lincolns 110 volt welders. i can carry it with one arm if i had to. you wouldnt need a big garage for it, just a 220 electrical outlet and a custom extension cord. remember a 220 welder will only require half the amperage of a 110 to do that same job. And as you know its the current that melts wiring, not voltage, so you could get away with 12 gauge cord and still weld heavier stuff.
btw mine is the same physical size, (or close to it) as many of lincolns 110 volt welders. i can carry it with one arm if i had to. you wouldnt need a big garage for it, just a 220 electrical outlet and a custom extension cord. remember a 220 welder will only require half the amperage of a 110 to do that same job. And as you know its the current that melts wiring, not voltage, so you could get away with 12 gauge cord and still weld heavier stuff.
It's my budget holding me back. I don't really have a need for it, but I'd like to have one.