Zuki750

old man roger

ouch .

old man roger

OMR SUBCAGE[S]
available subcages:
Honda

• CBR F4i - 01, 02, 03 <<< click here, will also fit the single seat style with minor mods
• CBR 954- all years
• CBR 929- all years <<< click here
• CBR 600RR - 03 , 04 , 05 , 06 , 07 , 08<<< click here

Kawasaki

• zx6r/rr (600/636) - 03, 04, 05, 06 07 08 09<<< click here

Suzuki

• GSXR 600 - 01, 02, 03, 04, 05 ,06, 07<<<click here
• GSXR 750- 00, 01, 02, 03, 04, 05, 06,07 <<click here
• GSXR 1000 -01, 02, 03, 04

Yamaha

• R6 - 03, 04, 05 <<< click here
• R6s (old body style) - 06, 07, 08
• R1 98, 99, 00, 01

$175 Shipped

pay pal accepted
Tech

• The CBR 600RR , Yamaha R6 ,03 04 gsxr 1000 and the f4i pegs are lowered and moved back and out for better peg position! !
• The 01-03 GSXR 600 and 750 have the pegs moved out two inches because of the big tail section
• THE 07 600RR pegs are located 2-1/2 inches lower and 3 inches wider (Than stock)
• The zx6 models are slightly wider than stock to keep your leg from being pressed against the tail
• other omr subframe cage models are in the stock location except they are rotated on their axis so they don't fold up unless you fold them up, this also puts your foot on the grippy part of the peg during a wheelie.
• omr subcages are available for all makes and models but only the ones listed above are available for shipping

click here to contact >> old man roger

the original folding peg subcage!!!!!!
>>click here to see why i only sell folding peg subcages<<

Trachito

you could learn to play left handed. jimmy played left handed... he probably was left handed, but still.

Zuki750

They don't look too bad there. When I did it, it squished all the fat and stuff out the ends of the fingers. The doctor just poked it back in and stitched me up.

MikeM

check this out
There are 3 18mm bolts that hold the bearing to the steering knuckle, that were on very very tight. Ihave 2 half inch impact guns, a top of the line kobalt thats rated for 650 and a bottom of the line Mac thats rated at 450. guess which one couldnt get the bolts out

Zuki750

Yeah, I don't think learning to play left handed would be all that easy. Plus, I already own 6 right handed guitars.

Trachito

have you tried stringing them upside down? i've never tried it but always been curious.

Zuki750

You'd need to replace the nut and then hope none of the controls or trem bars got in the way.

Trachito

couldn't you flip the nut upside down too? don't have to worry about a trem bar on an acoustic

Zuki750

You can't swap a nut, they are directional. I wouldn't just swap one guitar.

Trachito

you mean flip a nut? the nut sits in a slot so if a left handed guitar has a specific nut, it should fit on a right handed guitar. you'd just need to replace it. they aren't expensive, like 10-20 bucks, probably.

Zuki750

Yeah, flip a nut. I've replaced a nut before. I'm not spending 10-20 bucks to make my guitars unplayable. Plus the ergonomics would be off. Your cutaways would be on the wrong side, etc. Of course it's possible. Jimmy Hendrix did it.

Trachito

the pickups wouldn't have to be flipped or anything, right? they work the same throughout?

Trachito

i have to change a fret on my guitar. it has a razor thin cut in it and the string always falls into it. don't know how it got there all of a sudden.

Zuki750

Pickups are fine.

Zuki750

Take it to somebody. The cost of tools to do it correctly would be much more than a single fret replacement by a luthier.

old man roger

i learned a beach boys song on a guitar once and i wanted to learn to play but never followed through , at the time all i really cared about was cars

Trachito

i was thinking about doing that. i wonder how much it costs.

Zuki750

A single fret can't cost much more than $25 or so. I bet it's less than that.