12bar on a Dirtbike (PICS)
09-12-2005, 11:29 PM
#1
STOP THE BUCKING!!!!!!!!!
Thread Starter
Join Date: Jan 2005
Location: SO CAL
Age: 40
Posts: 7,720
12bar on a Dirtbike (PICS)
almost finished with 12bar for my 125, just got a few glitches to bang out
its got 2 sets of holes for 12 and slightly before 12, compliments of Johnny at Scrapeworks, their crashcages and bars will be out on the market soon
its got 2 sets of holes for 12 and slightly before 12, compliments of Johnny at Scrapeworks, their crashcages and bars will be out on the market soon
09-13-2005, 12:05 AM
#2
Registered User
Join Date: Jan 2005
Location: omaha
Age: 47
Posts: 732
Re: 12bar on a Dirtbike (PICS)
cut the two ends of the subframe off where they bend in towards each other. then bang 2 lenghts of 14mm steel rod in and weld it in place. after that run 2 more 14 mm steel rods up from the area of the smingarm attachment point up toa good spot on the subframe( again weld them in place)....otherwise that subframe is gonna snap after a few good hits and you'll be hurtin. i've seen it happen and it still looks painfull to this day when i watch the video od fiddycrazy snapping his subframe on his bike ina 3rd gear 12
other than that i'd say it looks good, i love stunting dirtbikes, they are so much more forgiving to the wallet and to leg bones
other than that i'd say it looks good, i love stunting dirtbikes, they are so much more forgiving to the wallet and to leg bones
09-13-2005, 12:29 AM
#3
STOP THE BUCKING!!!!!!!!!
Thread Starter
Join Date: Jan 2005
Location: SO CAL
Age: 40
Posts: 7,720
Re: 12bar on a Dirtbike (PICS)
your talkin about the yellow line i drew in the 2nd pic right? i dunno about the swingarm thing there isnt any good mount spots but i'll take a look at it again tomorrow. as for the ends that curve in im gonna weld two diagonal bars right above and drill them into the existing tube that oughta do the trick no?>
09-13-2005, 04:26 PM
#4
Registered User
Join Date: Jan 2005
Location: omaha
Age: 47
Posts: 732
Re: 12bar on a Dirtbike (PICS)
yea where teh 2 diaganal lines that say reinforece here.. where tehy bend in, you can cut them and hammer 14 mm bar stock in there, adn what i mean by near teh swingarm, is basicly where the bolt runs through to mount the swinger, just weld 2 pieces from that boxed metal area up to about midway throught hte subframe.
m ake all the difference in teh world as far as strength
m ake all the difference in teh world as far as strength
09-14-2005, 08:16 AM
#5
STOP THE BUCKING!!!!!!!!!
Thread Starter
Join Date: Jan 2005
Location: SO CAL
Age: 40
Posts: 7,720
Re: 12bar on a Dirtbike (PICS)
Originally Posted by turboglenn
yea where teh 2 diaganal lines that say reinforece here.. where tehy bend in, you can cut them and hammer 14 mm bar stock in there, adn what i mean by near teh swingarm, is basicly where the bolt runs through to mount the swinger, just weld 2 pieces from that boxed metal area up to about midway throught hte subframe.
m ake all the difference in teh world as far as strength
m ake all the difference in teh world as far as strength
09-14-2005, 10:02 PM
#6
STOP THE BUCKING!!!!!!!!!
Thread Starter
Join Date: Jan 2005
Location: SO CAL
Age: 40
Posts: 7,720
Re: 12bar on a Dirtbike (PICS)
finished product. subframe is reinforced all i need to do is chop back off and give it a go. :YEAH
www.scrapeworks.com
www.scrapeworks.com
09-17-2005, 09:16 PM
#8
STOP THE BUCKING!!!!!!!!!
Thread Starter
Join Date: Jan 2005
Location: SO CAL
Age: 40
Posts: 7,720
09-19-2005, 05:27 PM
#10
STOP THE BUCKING!!!!!!!!!
Thread Starter
Join Date: Jan 2005
Location: SO CAL
Age: 40
Posts: 7,720
Re: 12bar on a Dirtbike (PICS)
Originally Posted by ezec1000
i'm waiting...looks better on the computer than your camera..lets ROLL!!
fvcking RER still hasnt got my tire in, i guess i could just roll a huge endo all the way to brookfield??
Thread
Thread Starter
Forum
Replies
Last Post
