OMR SUBCAGE (S)
OMR SUBCAGES available:
Honda

• CBR F4i - 01, 02, 03 <<< click here, will also fit the single seat style with minor mods
• CBR 954- all years
• CBR 929- all years <<< click here
• CBR 600RR - 03 , 04 , 05 , 06 , 07 , 08<<< click here

Kawasaki

• zx6r/rr (636) - 03, 04, 05, 06 07 08<<< click here

Suzuki

• GSXR 600/750 -00, 01, 02, 03, 04, 05<<<click here
• GSXR 1000 -01, 02, 03, 04

Yamaha

• R6 - 03, 04, 05 <<< click here
• R6s (old body style) - 06, 07, 08

$175 Shipped
pay pal accepted

Tech

• The 03-06 CBR 600RR , 03-05 Yamaha R6 ,03 04 gsxr 1000 and the f4i pegs are lowered and moved back and out for better peg position! !
• The 01-03 GSXR 600 and 750 have the pegs moved out two inches because of the big tail section
• THE 07 600RR pegs are located 2-1/2 inches lower and 3 inches wider (Than stock)
• All other omr subframe cage models are in the stock location except they are rotated on their axis so they don't fold up unless you fold them up, this also puts your foot on the grippy part of the peg during a wheelie.
• omr subcages are available for all makes and models but only the ones listed above are available for shipping

click here to contact >> old man roger

the original folding peg subcage!!!!!!!!

>>click here to see why i only sell folding peg subcages<<

 

i'm out of minutes on my cell. this month's cell bill is gonna be bad due to going over on minutes. my **** don't renew until tuesday. fortunately nights and weekends are free.

 

my soldering technique, is heating the wires up, then as smoothly as i can apply the solder...

 

I finally get to yank my 9hundo out of the garage this weekend and clean it up to see how bad the Fire got it..

 

soldering isnt that bad, i learned at MMI Lol..

the hard part is gonna be trying to find the wires your talking about

 

he prolly could have had his game been on point. and maybe not at that time but in the future.

i want some chips.

 

hopefully the cow isnt too bad. is there anything left of the house

 

don't forget to put the heat shrink tubing on before you solder it...

 

+111110000000000000000

i havent had game since i left high school

 

Most the house is ok its both the double garages are toast...

VVV thats both the garages....

 

To give you an Idea of what it look like before...

 

heat shrink goes on after you solder the wires lol

 

**** man im sorry to hear about this. it sucks bad. atleast no one got hurt right.

 

Not if there is something connected to both sides of the wire..

 

that was a nice *** garage. i'd kill to have a garage that ******* nice... and a nicer house attached. u must be a baller, wheelie.

 

im ******* jealous thats a bad *** garage

 

I got 2nd deg burns on my left hand and around my right eye... but
doggys are ok..

 

just use some wires that are laying around the house. then look at the pics and solder them exactly where i explained.

 

I was about to say, why the **** would you be soldering a wire that isn't connected to anything.

Also make sure the heat shrink tubing doesn't shrink because of the heat from soldering. I have fucked that up more than a couple of times.

 

Was....
Again....was.....