gixxerkiid

i relayed clutch switch and took some pic here ya go

butt connected wires to some speaker wire hide but connectors in control wrapped wire in elec tape so they look clean


put control together zipp tied it


ran wires to battery area



pulled out starter relay


tested wires black with yellow tracer is positive starter wire from switch relay this wire so when it see positive it will connect clutch switch wires if you dont know how googel how a reay works and if your mechanically inclined you should firgure it out



ground relay


connect wires going to clutch switch wires


zip-tie your new relay out the way and put starter relay back where it came ffrom


put it back together and your done hope it helped

gixxerkiid

also removed servo from exhaust all you hve to do is take tail off and i got wrenchs in there with plastics on to get wires of servo on exhaust part then you just remove pin #30 on the black ecm plug it black with a brown tracer be sure to count because ther are two same color next to eachother its a 34 pin plug so it the 5th on back that makes it not throw a check engine light for not detecting exhaust servo taking out secondary butterflys tonight going to wait another week before i do the kleen air mod so its warmer out and the boots will go back on throttle bodies

Affiliated

why relay the clutch switch? whats to gain here by doing this?

gixxerkiid

because what the clutch is pulled in it acts as if these wire are touching eachother and it puts the bike in a "limp" mode which is like a zero map and when your pulling your clutch in and out doin slow wheelies it keeps the idle from acting different or if your like me the easy pull doesnt have a spot for the clutch switch but figured id show what i did ill have the secondary buttery fly removal all document along with clean air mod

gixxerkiid

why did you drill them out?

la66

Hello,everybody,the good shopping place,the new season approaching, click in. Let's facelift bar!
===== http://www.supershops.org ===

Air jordan(1-24)shoes $30

ugg BOOT $50

Nike (R4,NZ,OZ,TL1,TL2,TL3) $33

Handbags(Coach lv fendi d&g) $33

Tshirts (Polo ,ed hardy,lacoste) $16

Jean(True Religion,ed hardy,coogi) $30

Sunglasses(Oakey,coach,gucci,Armaini) $12

New era cap $9

Bikini (Ed hardy,polo) $18

FREE SHiPPING
( http://www.supershops.org )

Affiliated

kool -keep the info coming so I know what worth doing on mine next weekend

gixxerkiid

removing servo makes throttle wayyyy smoothers and responsive cant wait to do butterflys

motopsycho231

the little phillips head screws strip out SUPER easy and I rushed it and striped them all out but then I just drilled the little screws out in a drill press and the plates slide right out

I finally got to test it out and I LOVE IT. instant throttle response. Very smooth and no herky jerky jumping around. much much much better and NO FI LIGHT!!!! very happy and probablly the best mod I have done so far for this bike

motopsycho231

the exhaust servo is nothing compared to the butterflys

gixxerkiid

removed butterflys only got 3 of the 8 screw out woith a screw driver haha rest had to drill out and use a pic and magnet to make sure i got all the threads and metal shaving out but holy hell with out servo and butterfly thing does bog if your under 1500 rpm and give i a **** load of gas thats it haha the motor is crazy free reving in neutral u can crack throttle to 10 grand and it will fall right back down to were the idle is set no going up and down and being inconsistant like before love love love it can wait to make some slow wheelies makes it feel like more like and f4i motor just with more power soo smooth but hey who knows what long idle screw will fit in the stock idle adj. hole thanks

motopsycho231

I heard that you can use one off an old srad or something and that they are the same thread. I had to rethread mine and used one off a 600rr.

motopsycho231

Revive!!!! More power mods? Weight loss? Strength? I added a tre and liked that too but now I wanna lighten my tank up abit. Between the powers subcage and impaktech round bar and stay and fi cage this thing weighs a ton!

slowgsxr

back from the dead!! any more tips? bout to setup dirt bars, rsc lever, and rear handbrake , and r6 throttle tube on my k6 600.
ive been reading around about the TOS and saw a couple threads saying that you have to jump the TOS with resistors.
so hows the glue in the TOS working for you guys?

also does any have pics of how to do the secondary throttle valve mod?

LETS KEEP THIS THREAD GOING!!

PLU$MATIK