New 0 Degree Clip-Ons with Risers!!!
#42
#43
Re: stunning tattoos for hot race
PM Replied to! You need 50mm Clip-Ons.
#45
Re: New 0 Degree Clip-Ons with Risers!!!
#46
Re: New 0 Degree Clip-Ons with Risers!!!
The manufacturer is Swatt; www.swattmotorcycle.com. Our website is www.EndlessMoto.com, but these clip-ons haven't been added yet. PM me if you are interested in them.
Thanks!
#47
Re: New 0 Degree Clip-Ons with Risers!!!
I'm interested. Currently I have an 03/04 636 with a hohey upper triple an FI 0 degree bars. I'd like to maintain that current feel on my new street bike, but I can't decide on what rise to go with to maintain that. 0.5 inch? But then I'm also interested in seeing what a higher rise feels like
#48
Re: New 0 Degree Clip-Ons with Risers!!!
I'm interested. Currently I have an 03/04 636 with a hohey upper triple an FI 0 degree bars. I'd like to maintain that current feel on my new street bike, but I can't decide on what rise to go with to maintain that. 0.5 inch? But then I'm also interested in seeing what a higher rise feels like
#49
Re: New 0 Degree Clip-Ons with Risers!!!
If that's the case I would go with either the .5" rise or 1.5" rise; By having the HoHey Triple you can already run the bars on top obviously so you will get direct rise over the 0" the FI ones give you. If worst comes to worse and you want higher rise you can always get different riser plates alone and swap them out. I think 2.5" and 2.5" might be too high when on top of the HoHey Triple.
#50
Re: New 0 Degree Clip-Ons with Risers!!!
Sorry I misunderstood; If they are going under a stock triple I'd say go 3.5" rise and you can always lower them down the fork tubes to get less rise. That's what is so nice about these; adjustability is easy so you can fine tune to your preference.
#51
Re: New 0 Degree Clip-Ons with Risers!!!
Is anybody worried about putting so much pressure on the 2 little screws holding on the risers? Seems like the leverage from the risers would put a lot of strain directly on those 2 screws
Last edited by inolen; 03-25-2009 at 02:12 PM.
#53
Re: New 0 Degree Clip-Ons with Risers!!!
Why wouldn't you be able to use them? They should work fine.
#55
#57
Re: New 0 Degree Clip-Ons with Risers!!!
due to the way they mount,,like the pinch bolts might hit the inder part of the triple...
#58
Re: New 0 Degree Clip-Ons with Risers!!!
Next week I can try to fit them up on a customer's '07 ZX6R with a HoHey Triple and I will let you know. I don't think it will be an issue, but I can't say 100% for sure since I haven't had any HoHey setups installed yet.
#59
Re: New 0 Degree Clip-Ons with Risers!!!
cool man thanks cause i could use alil bit more height...like if i could raise my clips up a inch that would be dope...so im thinking the 5 degree ones swaped so they are angled up would be hot...
Last edited by havok; 03-26-2009 at 12:09 PM.
#60
Re: New 0 Degree Clip-Ons with Risers!!!
you would have to flip them to get up
ward angle wouldnt you?? that wouldnt work. if i were you for what you want i would have gotten the fullthrottle inc bar risers with flipped woodcraft clip-ons