Custom dirt bar setup 02 f4i
#41
#42
Re: Custom dirt bar setup 02 f4i
You can sink the forks in the tripples enough to clear the clamps.
It will actually help with endos and go ahead and raise the rear shock to match. This will help you have a wider balance point for endos and for wheelies :2CENTS
Did it to all my F4i's
It will actually help with endos and go ahead and raise the rear shock to match. This will help you have a wider balance point for endos and for wheelies :2CENTS
Did it to all my F4i's
#43
Re: Custom dirt bar setup 02 f4i
Good point.... I sank mine down just a tad, but not that much..
#44
Re: Custom dirt bar setup 02 f4i
I worked at a Harley Stealership for a long time and I was
the only one there that rode rocket... except for a few squids
that would get hired and act like a stupid jack *** and get let go
or couldn't deal with it...
#45
Re: Custom dirt bar setup 02 f4i
haha, speakin of Harley shops... I went to our ons sat. and just dropped my bike and walked in... there was a couple of guys in there that walked out and came back in screaming that somebody's bike had fell over... I laughed for hours. They were freakin out when I told them it was mine and it was cool.
#46
Re: Custom dirt bar setup 02 f4i
haha, speakin of Harley shops... I went to our ons sat. and just dropped my bike and walked in... there was a couple of guys in there that walked out and came back in screaming that somebody's bike had fell over... I laughed for hours. They were freakin out when I told them it was mine and it was cool.
outside smokin and I walked in like I didn't even care..
#47
Re: Custom dirt bar setup 02 f4i
#48
Re: Custom dirt bar setup 02 f4i
Was afraid to do that, If you dont mind, im going to pm you so you can tell me how you changed
the rear setup as well???
Last edited by ntseles; 02-05-2009 at 02:53 PM.
#49
Re: Custom dirt bar setup 02 f4i
I just raised the rear by tightening the spring all the way. I also unbolted the top mount of the shock that goes through the frame and stacked washers on it then out it back on and tightned it back up. It wont give you but about 1/2" there but by the time you get to the rear in hight it makes a noticeale dfference.
I alway put my fork caps flush with the triple.
It will still handle good if you do the front and the back. I wouldn't do one without the other.
#51
Re: Custom dirt bar setup 02 f4i
My pms are almost full.
I just raised the rear by tightening the spring all the way. I also unbolted the top mount of the shock that goes through the frame and stacked washers on it then out it back on and tightned it back up. It wont give you but about 1/2" there but by the time you get to the rear in hight it makes a noticeale dfference.
I alway put my fork caps flush with the triple.
It will still handle good if you do the front and the back. I wouldn't do one without the other.
I just raised the rear by tightening the spring all the way. I also unbolted the top mount of the shock that goes through the frame and stacked washers on it then out it back on and tightned it back up. It wont give you but about 1/2" there but by the time you get to the rear in hight it makes a noticeale dfference.
I alway put my fork caps flush with the triple.
It will still handle good if you do the front and the back. I wouldn't do one without the other.
I see, thanks for the info. Also, I wanted to ask you, how do you keep your front suspension? tight? soft? mid? Thanks again
Last edited by ntseles; 02-05-2009 at 04:32 PM.
#52
Re: Custom dirt bar setup 02 f4i
#53
Re: Custom dirt bar setup 02 f4i
I use these...
http://www.bambaracing.com.br/admin/produtos/168.jpg
http://www.bambaracing.com.br/admin/produtos/168.jpg
those are nice!
#55
Re: Custom dirt bar setup 02 f4i
I never ran risers with my f4i, just droped the forks like 1/2"
#56
#58
#59
Re: Custom dirt bar setup 02 f4i
I'm building a 01 929 right now with Pro tapers and not using the
controls...
I can't remember what risers I used on that one, But I am
using pro tapers on a RC51 Top triple for this build...
More pics to come...
Filled the Underneath and Drilled...
Then Mounted the Risers...