sick innovations, hell yeahhhh
#21
Re: sick innovations, hell yeahhhh
But the cage is avesome
Nothing has broken on my R6 even though it been through some hard crashes like this:
[youtube]http://se.youtube.com/watch?v=Pki136aWaDU&eurl=http://www.jonne-j.com/Highchaircircletraining.htm[/youtube]
#22
Re: sick innovations, hell yeahhhh
I hate americans for using INCH bolts and nuts!!!
But the cage is avesome
Nothing has broken on my R6 even though it been through some hard crashes like this:
http://se.youtube.com/watch?v=Pki136...letraining.htm
But the cage is avesome
Nothing has broken on my R6 even though it been through some hard crashes like this:
http://se.youtube.com/watch?v=Pki136...letraining.htm
Looks like your puttin it to the test. Congrats on turnin a few hc O's. Do you mind if we use this on our site?
#23
Re: sick innovations, hell yeahhhh
heres an SI cage being put to the test. check out CadillacZac @ 30 Sec.
http://www.vimeo.com/2597046
#24
Re: sick innovations, hell yeahhhh
heres an SI cage being put to the test. check out CadillacZac @ 30 Sec.
http://www.vimeo.com/2597046
http://www.vimeo.com/2597046
Hell yea. We could use this kinda footage. Is it ok to use just that small part of the clip?
#25
#26
#27
#28
#29
Re: sick innovations, hell yeahhhh
Guess I will buy me some inch sockets to have it easier in the future.
But once the cage is mounted itīs a tank and rock solid, 2 years of abuse and it still holds up fine.
#30
Re: sick innovations, hell yeahhhh
+1000 those inch bolts are a pain in the *** when putting on a cage with metric tools, especialy the all thread but you have no other option, 8mm will be to small and the motor sacks down, 10mm is to big and impossible to find a socket to fit the tubes.
Guess I will buy me some inch sockets to have it easier in the future.
But once the cage is mounted itīs a tank and rock solid, 2 years of abuse and it still holds up fine.
Guess I will buy me some inch sockets to have it easier in the future.
But once the cage is mounted itīs a tank and rock solid, 2 years of abuse and it still holds up fine.
I can look into maybe switching to metric 10mm all thread. Then 14mm socket would work..
#31
Re: sick innovations, hell yeahhhh
edit: 14mm socket does already work with your all thread, itīs just hard for us to find something to replace it if neccessary (if you mess up the thread while installing or you want a longer one to make it easier to mount up), your all thread has 9mm or something like that and itīs not to get over here.
Last edited by T'RIC'KY; 12-31-2008 at 12:00 PM.
#32
Re: sick innovations, hell yeahhhh
+1000 those inch bolts are a pain in the *** when putting on a cage with metric tools, especialy the all thread but you have no other option, 8mm will be to small and the motor sacks down, 10mm is to big and impossible to find a socket to fit the tubes.
Guess I will buy me some inch sockets to have it easier in the future.
But once the cage is mounted itīs a tank and rock solid, 2 years of abuse and it still holds up fine.
Guess I will buy me some inch sockets to have it easier in the future.
But once the cage is mounted itīs a tank and rock solid, 2 years of abuse and it still holds up fine.
#34
Re: sick innovations, hell yeahhhh
its impossible for the motor to sack down cause there are 3 other motormounts that bolt up to the frame, ie: swingarm, front motormounts where you also bolt the cage to and the mounts just before the cylinder, so its no problem at all if you use a 8mm treaded rod with 13mm bolts
#35
Re: sick innovations, hell yeahhhh
i can't see why the motor would sack down when there are 3 other motormounts that attach to the frame... the frame is solid on those 3 points... if anything could sack down the frame would come along
i'm also talking f4i here, maybe its different with the 954?
in the pic below i put a blue circel around the mount where the threaded rod goes and red circles where the other mounts go... imo there should be no problem at all if you used a smaller diameter of threaded rod as long as you tighten that sucker up good!
Thread
Thread Starter
Forum
Replies
Last Post
Sidsol
Bike Parts for Sale
3
02-07-2014 08:08 PM
sTuntjuNkief4i
Bike Parts for Sale
0
03-21-2013 01:12 AM