1000RR Frontend on F4i
#1
1000RR Frontend on F4i
I just picked up an F4i and im wanting to swap the front end asap. Just wanted to get some info from everyone before i started buying ****. I had a 954 frontend on my old f4i and i was satisfied with it but i just wanted to do something different this time. Is there a difference between 1000rr & 600rr
I was thinking of a 1000rr frontend on it? good or bad?
Is there anything i should know before getting into it?
I heard ppl use 954 lower triple for the clearance. yes? no?
I was thinking of a 1000rr frontend on it? good or bad?
Is there anything i should know before getting into it?
I heard ppl use 954 lower triple for the clearance. yes? no?
#3
Re: 1000RR Frontend on F4i
I just picked up an F4i and im wanting to swap the front end asap. Just wanted to get some info from everyone before i started buying ****. I had a 954 frontend on my old f4i and i was satisfied with it but i just wanted to do something different this time. Is there a difference between 1000rr & 600rr
I was thinking of a 1000rr frontend on it? good or bad?
Is there anything i should know before getting into it?
I heard ppl use 954 lower triple for the clearance. yes? no?
I was thinking of a 1000rr frontend on it? good or bad?
Is there anything i should know before getting into it?
I heard ppl use 954 lower triple for the clearance. yes? no?
#6
Re: 1000RR Frontend on F4i
#7
#9
Re: 1000RR Frontend on F4i
#10
Re: 1000RR Frontend on F4i
If so, make sure you install new ones!
If your bike goes flipping across the lot, without steering stops.. Expect your tank and/or frame to get dented to ****
#11
Re: 1000RR Frontend on F4i
#12
Re: 1000RR Frontend on F4i
i have a 1000rr front end i want to put on...how can i avoid the tire rubbing? ive heard of moving the radiator back but how do you do that with the bracket on the bottom?
and is the 954 lower triple the same width as the 1000rr lower? i heard if you use 954 lower that you would have to use a 954 wheel or axel too?
and how much do you grind down the steering stops exactly on a 1000rr lower triple if youre not supposed to grind them off completely?
and is the 954 lower triple the same width as the 1000rr lower? i heard if you use 954 lower that you would have to use a 954 wheel or axel too?
and how much do you grind down the steering stops exactly on a 1000rr lower triple if youre not supposed to grind them off completely?
#14
Re: 1000RR Frontend on F4i
I got 929/54 wheel, lower n upper trip 1krr forks... Clipons underneath i hit rad reguarly during stoppies.... U gotta run clips under fo sho
Im tryin to cop a rc51 top tripple....hope that helps
Im tryin to cop a rc51 top tripple....hope that helps
#15
Re: 1000RR Frontend on F4i
I got 929/54 wheel, lower n upper trip 1krr forks... Clipons underneath i hit rad reguarly during stoppies.... U gotta run clips under fo sho
Im tryin to cop a rc51 top tripple....hope that helps
Im tryin to cop a rc51 top tripple....hope that helps
#16
Re: 1000RR Frontend on F4i
what is the advantage of using rc51 top tripple? does it give more room to run clip ons on top?
#19
#20
Re: 1000RR Frontend on F4i
i have a 1krr setup with clipons on top i took the bottom bracket to the radiator and cut about an inch of and re-drilled it. bingo bango no tire rubbing!