Sportmax

So i finally got my F4I done. Brand new SI cage and subframe cage on it, and a ton of other **** i had to fix. Im all ready to go stunt it for the first time, but its been to snowy and cold. We finally got a nice enough day sunday to go ride, i load up the bike in the truck and head to our spot. Unload it, fire it up, ride about 20 yards and it shuts off. Felt like i hit the kill switch. Wouldnt start again, no crank nothing,acted just like the kill switch was shut off. So with no tolls on us we couldn't fix it and it ruined my day

All i can say is maybe it was a sign that i shouldn't have been riding that day

Lil Krazy

you fix it?

illegal_skillz

That sucks, all that waiting for nothing

Sportmax

Havnt had time to look at it yet. Probably check it out tonight. Its probably just some dumb electrical problem that will take 10 min to fix

illegal_skillz

At least you hope that's all it is

Lil Krazy

It could be alot of things fuses battery, wiring the kickstand sensor, something inside your kill switch. i could go on and on

KoleDSF

you live in highlands ranch? everywhere i looked to ride was still icy and wet...

EEKENTERPRISES

Make sure the tipover sensor isn't hanging somewhere...ff or sf?

Sportmax

We went to Havanna and I70. The lot was pretty much dry besides just a little water run off on the edges.

Im thinking kill switch went bad but no clue. Going to remove the tip over sensor just to eliminate it so i know its not the problem.

Sportmax

ff or sf???? what i am not getting??

illegal_skillz

Is the bike full fairing or streetfighter?

EEKENTERPRISES

If you need any help let me know, I just pulled mine completely out last weekend.... never have to worry about it again....

Sportmax

HAHAHHAHA wow cant believe i couldn't figure that one out
Its a full fairing, race fairings.

Hopfully i shouldn't need any help but ill definitly let you know if i do

illegal_skillz

It's alright bro, it happens to the best of us

EEKENTERPRISES

I'll post this up as it takes me 2 seconds and if it helps you, cheers!!!
Did this last night.....clean air mod and removal of the tip over sensor as I still love that wheelie sensation!!!
The clean air mod will give you better low end for two reasons ... this is why racers love it.....

1- you don't get any of the hot oily air from the crank case in your airbox---Take an automotive spray gun, The air blowing by the small jet pulls paint from the canister and doesn't blow pressure into the can...... Same thing here, the exhaust blows by and pulls the hot air / oil from the crancase with it...
2- by hooking the crankcase vent tube up to the clean air valve it creates a vaccum in the crank case and that is good for a few extra horse power and a couple foot pounds of torque...OMR (aka the man) said..."it makes the bike better all around and alot of people agree ,i have even seen dyno test that show increased torque and horse power"
The stunters love it because it prevents a hydrolock situation from the bike being on its side and oil being dumped into the airbox from the breather tube....it has been argued over and over and proven, this is a great mod with no bad side effects whatsoever....

This is what it looks like stock....the directions are a bit confusing, throw 3 away, and hook 1 2 and 4 to the new t....


The pair valve removed....

1/2" Tee...it was very tight, had to vaseline the hoses to get them on, but better than too loose....

Here is a pic of the t with the hoses.....


How I sealed the airbox off, I have seen many methods, but looking around the garage I realized that some old tire valve cover caps fit perfectly and are hard enough to hold, through them in with a little epoxy and they were solid and fit perfect, looks factory...



Also here is the tipover sensor mod as well.... just cut that damn thing out and never worry about it again....
With windscreen off...

Remove the 2 screws holding the box in and disconnect the box...

Here it is removed and unclipped....

Cut off the connector and make sure there is enough room to reconnect if you want to reinstall in the feature, tie red and green together and cap white off....and clip back in....

Sportmax

Thats freaken awsome man:YEAH . THanks.

Ive been trying to figure out the clean air mod and i know exactly what to do now. The tip over sensor is going to be easy as hell.

zxcraig

good info with pics!!

illegal_skillz

Holy ****, you're an overachiever, that's cool though, that's some really good help. SL needs more like you

Lil Krazy

You can also do the air mod by keeping the silver thing there you take it apart and pull the spring and other thing out and elimanate the long hose tape off the air box and your good to go good post though

:YEAH

illegal_skillz

You lost me bro. But let me try, I keep the silver thing but pull it apart and remove the spring and other thing out, then I elimanate the long hose, tape off the air box and I'm good? I thought I had to take the thing out of the thing and put the dohunky in the whatchamacallit? Maybe I'm wrong
Yeah, I think I got it now