05/06 636 stunt stays, need some input from riders.
#61
#62
Re: 05/06 636 stunt stays, need some input from riders.
Mine is a flipped right hand master, I wanted the left hand clutch 13 but I cannot find anyone that brings those into the US. Magura does make it but its hard to get in the US, and I didnt feel like payed an extra $100 to order it direct from Magura..
Also I run my clutch on the inside and my HB on the outside, if you run this way a left hand will not fit(the res fitting get in the way). If you run your setup the other way around it would be perfect though...
PS For the 05/06'ers I got a new frame off someone on here deliverd yesterday, and spent all last night putting the old VIN on it and reassembling the bike. So Ive got the bike FF and Im gonna work on designing the stay over the holidays, hopefully I'll have something ready to show you guys after Chrismass....
Also I run my clutch on the inside and my HB on the outside, if you run this way a left hand will not fit(the res fitting get in the way). If you run your setup the other way around it would be perfect though...
PS For the 05/06'ers I got a new frame off someone on here deliverd yesterday, and spent all last night putting the old VIN on it and reassembling the bike. So Ive got the bike FF and Im gonna work on designing the stay over the holidays, hopefully I'll have something ready to show you guys after Chrismass....
Last edited by JohnnyP; 12-22-2007 at 02:46 PM.
#63
#65
Re: 05/06 636 stunt stays, need some input from riders.
#67
Re: 05/06 636 stunt stays, need some input from riders.
I feel so bad about taking a hacksaw to my johnnyP stay. I chopped it down earlier this season all the way to the guage cluster when I was running 0 degree's. If I was smart I woulda kept the piece and had it rewelded, but I junked it.
#68
Re: 05/06 636 stunt stays, need some input from riders.
#69
Re: 05/06 636 stunt stays, need some input from riders.
[quote=JohnnyP;3075921]Mine is a flipped right hand master, I wanted the left hand clutch 13 but I cannot find anyone that brings those into the US. Magura does make it but its hard to get in the US, and I didnt feel like payed an extra $100 to order it direct from Magura..
Also I run my clutch on the inside and my HB on the outside, if you run this way a left hand will not fit(the res fitting get in the way). If you run your setup the other way around it would be perfect though...
quote]
ohh ok, dont they have a left handed one in the us? but isnt it a 16?
Also I run my clutch on the inside and my HB on the outside, if you run this way a left hand will not fit(the res fitting get in the way). If you run your setup the other way around it would be perfect though...
quote]
ohh ok, dont they have a left handed one in the us? but isnt it a 16?
#70
Re: 05/06 636 stunt stays, need some input from riders.
It's so useless now.. no cross bar, and I have no headlights to help support the upper fairing. I'll fix it though, somehow.
#71
Re: 05/06 636 stunt stays, need some input from riders.
There is nothing illegal about stamping a legit frame with legit numbers, my friends frame cracked and I bought a salvage title frame to replace it. Its cheaper for me to put my friends old salvage numbers back on the new frame, rather then have to import and register the new one. Its the same thing as ordering a blank frame from Kawi and stamping it, just cheaper.....
#72
Re: 05/06 636 stunt stays, need some input from riders.
[QUOTE=Afflicted;3076762] Yes the only left hand master they carry in the US is the 16, no one has the 13 in a left.
And I just tried out the 13 and that is what you want, TRUST ME!
Mine is a flipped right hand master, I wanted the left hand clutch 13 but I cannot find anyone that brings those into the US. Magura does make it but its hard to get in the US, and I didnt feel like payed an extra $100 to order it direct from Magura..
Also I run my clutch on the inside and my HB on the outside, if you run this way a left hand will not fit(the res fitting get in the way). If you run your setup the other way around it would be perfect though...
quote]
ohh ok, dont they have a left handed one in the us? but isnt it a 16?
Also I run my clutch on the inside and my HB on the outside, if you run this way a left hand will not fit(the res fitting get in the way). If you run your setup the other way around it would be perfect though...
quote]
ohh ok, dont they have a left handed one in the us? but isnt it a 16?
And I just tried out the 13 and that is what you want, TRUST ME!
#73
Re: 05/06 636 stunt stays, need some input from riders.
there's 2 t's in attention chief....
again.... PUBLIC FORUM... anyone can see it... no need to attract attention if someone is already looking for something in perticular...
Last edited by kj; 12-23-2007 at 02:26 AM.
#74
Re: 05/06 636 stunt stays, need some input from riders.
There is nothing illegal about stamping a legit frame with legit numbers, my friends frame cracked and I bought a salvage title frame to replace it. Its cheaper for me to put my friends old salvage numbers back on the new frame, rather then have to import and register the new one. Its the same thing as ordering a blank frame from Kawi and stamping it, just cheaper.....
whatever.. just tryin to be helpful..... unlike most douche bags that roam this board.
#75
Registered Spammer
Join Date: Apr 2004
Location: 1101 Main Street North, Austin, MN, United States
Age: 41
Posts: 38,851
Re: 05/06 636 stunt stays, need some input from riders.
You mean three right?
Best Car & Motorcycle Insurance | Auto/Moto Protection Today | FREE Trade-In Quote
Best Car & Motorcycle Insurance | Auto/Moto Protection Today | FREE Trade-In Quote
#76
Re: 05/06 636 stunt stays, need some input from riders.
Ok guys I got really motivated today and just finished designing the 05/06 stay, been here 12 hours straight but its finally done. My new CAD/CAM program made it alot easier to get the parts drawn up and fitting properly, used to spend a few days doing this....
This is what its going to look like, the MDF will obviously be replaced with plate aluminum. I use MDF for the design stage then from here I have the same shapes cut out of aluminum sheets for me..
Im going to try and get another die made for my bender to try and match the cross bar to the windscreen a little better, for now thats the best I could do with my crappy bender and limmited dies...
Im really happy with the way I was able to support the headlight, it will have the 2 top mounts that are pretty strong(much stronger then the 03/04's). And also 2 more bolts that will mount right through the top of the headlight housing..Just like my 03/04 636 stays these add up to a very sturdy upper/headlight setup....
For now Im happy with it and hopefully when I get the parts cut out of aluminum after Christmass, everything fits good and I dont have to make any major adjustments...Let me know what you guys think
This is what its going to look like, the MDF will obviously be replaced with plate aluminum. I use MDF for the design stage then from here I have the same shapes cut out of aluminum sheets for me..
Im going to try and get another die made for my bender to try and match the cross bar to the windscreen a little better, for now thats the best I could do with my crappy bender and limmited dies...
Im really happy with the way I was able to support the headlight, it will have the 2 top mounts that are pretty strong(much stronger then the 03/04's). And also 2 more bolts that will mount right through the top of the headlight housing..Just like my 03/04 636 stays these add up to a very sturdy upper/headlight setup....
For now Im happy with it and hopefully when I get the parts cut out of aluminum after Christmass, everything fits good and I dont have to make any major adjustments...Let me know what you guys think
Last edited by JohnnyP; 12-24-2007 at 05:05 AM.