my fucking sick innovations piece of shit subframe cage
10-03-2007, 12:25 AM
#23
Registered User
Join Date: Nov 2004
Location: South of Boston, 781
Posts: 2,277
Re: my ******* sick innovations piece of **** subframe cage
1st of all stock tabs DO NOT bend outward
Second... he does not have a bad jig... the subcage is supposed to be tight as **** to get on... but if you have some ******* brains you will figure out that if you get one side on and have someone else pull/push, it'll slide on...
I highly doubt it's off by a 1/2in... but if it really is then let him know (leave a voice mail :rolleyes), and he will make it right. Do you really think that he's got a jig that's off by a 1/2in and NOBODY elses has been on here complaining about it?
Don't come cryin on here cause your too ******* stupid to get it on your bike w/ out instructions..... nobody cares.
Idiot
Last edited by kj; 10-03-2007 at 12:27 AM.
10-03-2007, 12:32 AM
#24
Registered User
Join Date: Apr 2006
Location: Apple Valley CA
Age: 43
Posts: 4,923
10-03-2007, 12:33 AM
#25
Registered User
Join Date: Apr 2006
Location: Apple Valley CA
Age: 43
Posts: 4,923
Re: my ******* sick innovations piece of **** subframe cage
1st of all stock tabs DO NOT bend outward
Second... he does not have a bad jig... the subcage is supposed to be tight as **** to get on... but if you have some ******* brains you will figure out that if you get one side on and have someone else pull/push, it'll slide on...
I highly doubt it's off by a 1/2in... but if it really is then let him know (leave a voice mail :rolleyes), and he will make it right. Do you really think that he's got a jig that's off by a 1/2in and NOBODY elses has been on here complaining about it?
Don't come cryin on here cause your too ******* stupid to get it on your bike w/ out instructions..... nobody cares.
Idiot
Second... he does not have a bad jig... the subcage is supposed to be tight as **** to get on... but if you have some ******* brains you will figure out that if you get one side on and have someone else pull/push, it'll slide on...
I highly doubt it's off by a 1/2in... but if it really is then let him know (leave a voice mail :rolleyes), and he will make it right. Do you really think that he's got a jig that's off by a 1/2in and NOBODY elses has been on here complaining about it?
Don't come cryin on here cause your too ******* stupid to get it on your bike w/ out instructions..... nobody cares.
Idiot
10-03-2007, 12:45 AM
#28
Squid Supreme
Join Date: Apr 2007
Location: Hot Springs, Arkansas
Age: 35
Posts: 1,660
Re: my ******* sick innovations piece of **** subframe cage
Well, that's why most people don't stunt a mint bike.
10-03-2007, 03:53 AM
#29
Registered User
Join Date: Apr 2004
Location: Melbourne, AUS
Age: 43
Posts: 550
Re: my ******* sick innovations piece of **** subframe cage
hey calm down dude. it will fit.
what happens is that when the cross brace gets welded, and the weld cool down, the tabs will pull slightly closer together. this is fine.
just get the one tab sitting on the subframe tabs on one side, and the other side close to the tabs. then as you are lifting the subframe up, use a flat pry bar to open the tabs a little wider. it will slide on - guaranteed. might help to have another person assist.
don't cut or grind any tabs because... a) you don't need too. b) you might void your SI warranty
they're made in a jig so they will fit
(i have no affiliation with SI - i just have an SI subcage)
what happens is that when the cross brace gets welded, and the weld cool down, the tabs will pull slightly closer together. this is fine.
just get the one tab sitting on the subframe tabs on one side, and the other side close to the tabs. then as you are lifting the subframe up, use a flat pry bar to open the tabs a little wider. it will slide on - guaranteed. might help to have another person assist.
don't cut or grind any tabs because... a) you don't need too. b) you might void your SI warranty
they're made in a jig so they will fit
(i have no affiliation with SI - i just have an SI subcage)
10-03-2007, 05:00 AM
#30
WWW.Sickinnovations.com
Join Date: May 2004
Location: Usa
Posts: 18,216
Re: my ******* sick innovations piece of **** subframe cage
dumbass people that start threads like this deserve no customer service or help from other people. 
give him a chance to make it right before you flame on someone Asshat
oh and its my fault it is going to snow where you live
give him a chance to make it right before you flame on someone Asshat
oh and its my fault it is going to snow where you live
10-03-2007, 05:40 AM
#31
Registered User
Join Date: Jul 2007
Location: Anchorage, alaska usa
Age: 39
Posts: 1,087
Re: my ******* sick innovations piece of **** subframe cage
Could be misfabricated as you seen the tabs different in a picture..
Or for a different year bike..
Chill out.. Go talk to a welder. Put some time into it.. Use your head.
I'd make it fit.. !!
Or for a different year bike..
Chill out.. Go talk to a welder. Put some time into it.. Use your head.
I'd make it fit.. !!
10-03-2007, 08:51 AM
#33
Registered User
Join Date: Jul 2005
Location: louisville, Ky.
Age: 44
Posts: 2,521
Re: my ******* sick innovations piece of **** subframe cage
uh i dont see any tabs bent ....hey everyone isnt perfect sometimes they made a mistake for a good reason so i m sure ian is more happy to take care of ya to return it and send you another one. and yet i had alot of patience with ian for almost 4 weeks on my round bar and cage so i busted my stator last night ..imma not gunna run and cry to ian....my point is that all you can do talk with him on phone and explain what is the mistake is.
either way even if it's taken care of... spending that much $, and witing to have to wait on another one SUCKS.. but them ******* are dope looking as hell! :YEAH
10-03-2007, 09:55 AM
#34
YUT UGH
Join Date: Feb 2007
Location: Cincinnati, Ohio
Posts: 1,570
Re: my ******* sick innovations piece of **** subframe cage
its probly a subcage for a 636, i think im going to get one tho....they are sexy, doesnt it take for ever to get a powers one tho? thats what i heard
10-03-2007, 09:56 AM
#35
Registered User
Join Date: Nov 2004
Location: South of Boston, 781
Posts: 2,277
Re: my ******* sick innovations piece of **** subframe cage
hey calm down dude. it will fit.
what happens is that when the cross brace gets welded, and the weld cool down, the tabs will pull slightly closer together. this is fine.
just get the one tab sitting on the subframe tabs on one side, and the other side close to the tabs. then as you are lifting the subframe up, use a flat pry bar to open the tabs a little wider. it will slide on - guaranteed. might help to have another person assist.
what happens is that when the cross brace gets welded, and the weld cool down, the tabs will pull slightly closer together. this is fine.
just get the one tab sitting on the subframe tabs on one side, and the other side close to the tabs. then as you are lifting the subframe up, use a flat pry bar to open the tabs a little wider. it will slide on - guaranteed. might help to have another person assist.
Sorry buddy... but this is true
Last edited by kj; 10-03-2007 at 10:04 AM.
10-03-2007, 10:16 AM
#36
also known as OMR
Join Date: Jul 2006
Location: OMR INDUSTRIES in west palm beach florida
Posts: 79,288
Re: my ******* sick innovations piece of **** subframe cage
ok i have an idea .......two peices of threaded rod long enough to go from one side to the other [through the mounting holes] use two nuts and two washers on each peice of threaded rod to spread the mounting tabs apart
10-03-2007, 10:19 AM
#37
Registered User
Join Date: Jul 2005
Location: louisville, Ky.
Age: 44
Posts: 2,521
Re: my ******* sick innovations piece of **** subframe cage
damn OMR..... ill have to remember that one
ol dude might be right "shipped him a 636 subcage"
**** happens.... dont know if there is much difference in them
10-03-2007, 10:38 AM
#38
Registered User
Join Date: Mar 2007
Location: C-TOWN, IN
Age: 45
Posts: 523
Re: my ******* sick innovations piece of **** subframe cage
10-03-2007, 10:42 AM
#39
sickinnovations.com
Join Date: Mar 2004
Location: EVANSVILLE
Age: 45
Posts: 2,217
Re: my ******* sick innovations piece of **** subframe cage
Ok. for starters. They arent BMX pegs. We make them on our lathe from solid aluminum. 2. Call the shop line between business hours. ( the number on the site) I will not answer my cell number. 3. We rarely return calls due to the call volume every day. Just call back the next day when we open. 4.. The jig is not off. We have sold many and you are the 1st to mention this. This subcage is for the dual seat f4i subframe, not the bananna seat. That may be your problem. Questions can be answered. All you have to do is ask. You may want to listen to others before flaming us on here. What enjoyment did you get from this thread? I dont understand internet gangstas at all. We do everything we can to get orders out in a timely fashion and to keep customers happy.
10-03-2007, 10:45 AM
#40
Registered User
Join Date: Jun 2004
Location: CT
Age: 42
Posts: 1,057
Re: my ******* sick innovations piece of **** subframe cage
Its a good idea, but the rod will be in the way. You won't be able to get it out of the holes, or its going to shoot out.
Get one side on, and slide the other side on with a large flat screwdriver, or pry bar.
