Startin out
#1
Registered User
Thread Starter
Join Date: Sep 2006
Location: Dont know...it's dark in here
Posts: 507
Startin out
Aight guys, got a 05 gixxer that's sf right now but was wondering what would be the best setup for it to stunt it out? got -1 in the front, stock on the rear, full yoshi system with a stubby rs3 pipe. I wanna get a 12 bar but my buddy say's they're unforgiving compared to a round bar.
All comment's in good natuire are greatly appreciated....
All comment's in good natuire are greatly appreciated....
#6
Re: Startin out
run stock exhaust if you can. For one, its more stealthy and less annoying. Two, it gives you better low end.
I would only get a 12 bar once you've mastered rear brake control. It is way cheaper and easier to replace tails than it is to replace or repair subframes. Same requirement goes for getting gearing. If you get gearing when you're not ready, it'll just make it harder to learn cuz it will be so touchy and jerky.
I would only get a 12 bar once you've mastered rear brake control. It is way cheaper and easier to replace tails than it is to replace or repair subframes. Same requirement goes for getting gearing. If you get gearing when you're not ready, it'll just make it harder to learn cuz it will be so touchy and jerky.
Last edited by solidjohnny; 10-01-2006 at 08:04 PM.
#10
Registered Spammer
Join Date: Apr 2004
Location: 1101 Main Street North, Austin, MN, United States
Age: 41
Posts: 38,851
Re: Startin out
Sell any good plastic and sell the yoshi.
Best Car & Motorcycle Insurance | Auto/Moto Protection Today | FREE Trade-In Quote
Best Car & Motorcycle Insurance | Auto/Moto Protection Today | FREE Trade-In Quote
#11
Registered User
Thread Starter
Join Date: Sep 2006
Location: Dont know...it's dark in here
Posts: 507
Re: Startin out
dayum, see this is the stuff my boy's here in H-town can't tell me. Thanks for all the info. Right now, my sub-frame is braced with like 1/4" alu. flatbar.... ...that's what my bud, who stunt's, said helps. But the thing is I wrecked it trying to 12 and snapped the lower end where my right rearset is. Don't really know what I can do, if anything, to delay that but like I said any info helps. Thank's again, but I gotta roll out and hit up my spot to practice.....:YEAH
#12
Re: Startin out
I say get you self 10-12 tooth rear . and do it soon , so when you ride with it you will get use to it. Other than learning one way then changin your bike and have to learn all over again.
#13
Registered User
Thread Starter
Join Date: Sep 2006
Location: Dont know...it's dark in here
Posts: 507
Re: Startin out
Hahahahaha....dayum bro...you dug up this old corpse....LOL
Actually, i've gotten alot better since then. Benn practicing on my buddy's F4izzle. Got down FIB, FIB O's, SS, spreaders and sitdowns. I'm actually gettin my own crunchy piece finally, and it'll be the gixxer again...LOL....go figure? Right now it's got 7 up in the rear but I gotta fix the idle on it....
Actually, i've gotten alot better since then. Benn practicing on my buddy's F4izzle. Got down FIB, FIB O's, SS, spreaders and sitdowns. I'm actually gettin my own crunchy piece finally, and it'll be the gixxer again...LOL....go figure? Right now it's got 7 up in the rear but I gotta fix the idle on it....
Thread
Thread Starter
Forum
Replies
Last Post